-
- News
- Books
Featured Books
- pcb007 Magazine
Latest Issues
Current IssueThe Sustainability Issue
Sustainability is one of the most widely used terms in business today, especially for electronics and manufacturing but what does it mean to you? We explore the environmental, business, and economic impacts.
The Fabricator’s Guide to IPC APEX EXPO
This issue previews many of the important events taking place at this year's show and highlights some changes and opportunities. So, buckle up. We are counting down to IPC APEX EXPO 2024.
Getting to Know Your Designer
In this issue, we examine how fabs work with their design customers, educating them on the critical elements of fabrication needed to be successful, as well as the many tradeoffs involved. How well do you really know your customer? What makes for a closer, more synchronized working relationship?
- Articles
- Columns
Search Console
- Links
- Events
||| MENU - pcb007 Magazine
Thin PCBs for Smart Phones: Technology and Reliability Considerations
November 19, 2014 |Estimated reading time: 1 minute
Abstract
The next generation of smartphones will demand very thin multilayer boards to reduce product thickness again. This paper shows three different manufacturing approaches which can be used for very thin, any-layer build-ups. The technological approaches are compared on reliability level—the any-layer copper filled microvia technology which is to be considered as state-of-the-art technology for high-end phones and the ALIVH-C/G technology that is well established in Japan.
A test vehicle design featuring test coupons for comprehensive reliability test series has been defined as target application for investigation. The applied test vehicle build-ups comprise an eight-layer build-up with total board thickness below 500 µm. The first test vehicle is based on an any-layer HDI build-up including copper filled stacked microvia structures, the second test vehicle features a 1+6+1 ALIVH-C build-up comprising an outer HDI prepreg layer, while the third test vehicle is built in ALIVH-G technology featuring a full ALIVH build-up.
The influence of the applied manufacturing technology on the reliability performance of thin PCBs is evaluated based on these three test vehicle build-ups.
To cover the behavior during SMD component assembly the produced samples are subjected to reflow sensitivity testing applying a lead-free reflow profile with a peak temperature of +260ºC. Failure occurrence and the observed failure modes are evaluated and compared.
In parallel, a temperature cycling test is conducted on the test vehicles in a temperature range between -40ºC and +125ºC to evaluate the thermo mechanical reliability of the test vehicles with regard to the manufacturing technology.
To characterize the reliability aspects influenced by electrochemical migration phenomenon the different samples are subjected to a HAST test at +130ºC with 85% humidity level.
The results obtained from reliability testing are summarized and compared within this paper. The identified relations between manufacturing technology and the reliability performance of the test vehicles are shown; strengths as well as weaknesses of the applied any-layer technologies are identified and summarized.
Read the full article here.
Editor's Note: This article originally appeared in the October issue of The PCB Magazine.
Suggested Items
Elementary, Mr. Watson: Ensuring Design Integrity
03/28/2024 | John Watson -- Column: Elementary, Mr. WatsonBack in February, many of us watched the "Big Game." It reminded me of the saying, “It's not how you start that is important, but rather how you finish." It is perfectly okay when you are talking about sports, you get off to a bad first half and need to recover in the second half. However, when it comes to PCB design, this is not a good practice. If things start badly, they usually don't recover. They continue down that same path, costing more money and losing design time.
Punching Out: Acquiring a PCB/EMS Shop: Brownfield vs. Greenfield
03/27/2024 | Tom Kastner -- Column: Punching Out!We often get asked about establishing a new company (greenfield) rather than buying an existing PCB or EMS shop (brownfield). There are many criteria to consider. Many buyers want to grow through M&A, but they cannot find acquisition targets that fit their criteria. Perhaps they can find the right shop, or at least one that fits five out of 10 criteria, but they encounter obstacles, such as owners who do not want to sell, price expectations that are too high, or negotiations that are too difficult. Despite the interest in building new facilities, since 2000, few companies have gone the greenfield route. Here is a look at the pros and cons of buying vs. building.
Ventec to Launch New Bondply Dielectrics and Value-Added Services at IPC APEX EXPO 2024
03/26/2024 | Ventec International GroupVentec International Group is to reveal new products for advanced signal integrity and thermal performance, and introduce services, during IPC APEX EXPO 2024, April 9-11 on booth # 4309.
North American PCB Industry Sales Down 11.6% in February
03/25/2024 | IPCIPC announced today the February 2024 findings from its North American Printed Circuit Board (PCB) Statistical Program. The book-to-bill ratio stands at 1.07.
Benmayor to Exhibit Technosystem Automation at IPC APEX EXPO 2024
03/25/2024 | BenmayorBenmayor will exhibit Technosystem Automation at the IPC APEX EXPO 2024, a world-class trade show and cutting-edge technical conference in Anaheim, California, April 6-11, in booth 4432 at Burkle North America (Schmoll).